It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
After you reach as far as you can go, add some water to the hole. You don't have to fill the hole, just make it moist so you can begin pushing the rod in by hand. The water will help with this process. As you go deeper with the pole, add more water to help out. You can move the pole back and forth with the pointed end in the ground to make it easier. Once you reach the point it won't go deeper by hand, grab another tool.
After you have the rod a couple of feet into the ground, start hammering. There will be a point where it just won't go in manually anymore. If you do not have a driver, which is placed over the top of the rod allowing you to easily drive it in, you can put a board over it to make a bigger surface to hit. Keep hammering and driving it until there is just an inch or two sticking above the top of the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
After you reach as far as you can go, add some water to the hole. You don't have to fill the hole, just make it moist so you can begin pushing the rod in by hand. The water will help with this process. As you go deeper with the pole, add more water to help out. You can move the pole back and forth with the pointed end in the ground to make it easier. Once you reach the point it won't go deeper by hand, grab another tool.
After you have the rod a couple of feet into the ground, start hammering. There will be a point where it just won't go in manually anymore. If you do not have a driver, which is placed over the top of the rod allowing you to easily drive it in, you can put a board over it to make a bigger surface to hit. Keep hammering and driving it until there is just an inch or two sticking above the top of the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
No comments:
Post a Comment