Once upon a time televisions were mostly made up of tubes encased in wood, wires, knobs, scanners, and rabbit ears. As with most things, televisions have become much more complicated and technical in today's world. Even though you may not have any plans to become a television repair person, you might still be interested in learning about the boards, such as the T-Con d50ud1, inside LCD tvs, if the science of electronics intrigues you.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
Direct current, or DC, moves in only one direction. The circuit located in the LCD television uses this. You may find the inverter board and the power supply module joined in some televisions. If you're experiencing a lack of power, or only intermittent power, the power supply board may be malfunctioning.
The timing control board, or T-con, is the smallest board in the television. It is pretty much only found in LCD tvs. You'll probably find it under a shield toward the top of the back of the television.
The T-Con board is there to control the TFT, thin film transistor, driver and the circuit. If you're experiencing horizontal or vertical lines you may be having trouble with the timing control board. Other indications are a white screen, a double image, or no image at all.
You will find the inverter board at the back along the television's edge. If you have any tv other than an LCD, there will be no inverter board. This board is on the tv in order to convert the low voltage direct current, that the switched mode power supplies, into high voltage alternate current. Backlights are lit up with this. Inverters boards are sometimes combined with power boards. If your inverter board goes bad, you may see a dim screen or a display that shuts down entirely.
The main board is also known as the motherboard, the logic board, the main module, and the digital board. This is going to be the board on the back of the television that has the sound and video inputs and outputs attached to it. The main board is what takes in the signals and converts analog into digital. If you don't have color or sound, have vertical lines, or no picture, the main board may be the culprit.
The audio receiving board or jackpack can be separated from the motherboard. The jackpack moves the sound signal to a processor and then to the amplifiers that are on either side of your television. If you can't get any sound, or hear a high pitched tone, the jackpack can be the culprit. You should check out the jackpack if the channels start to change randomly.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
Direct current, or DC, moves in only one direction. The circuit located in the LCD television uses this. You may find the inverter board and the power supply module joined in some televisions. If you're experiencing a lack of power, or only intermittent power, the power supply board may be malfunctioning.
The timing control board, or T-con, is the smallest board in the television. It is pretty much only found in LCD tvs. You'll probably find it under a shield toward the top of the back of the television.
The T-Con board is there to control the TFT, thin film transistor, driver and the circuit. If you're experiencing horizontal or vertical lines you may be having trouble with the timing control board. Other indications are a white screen, a double image, or no image at all.
You will find the inverter board at the back along the television's edge. If you have any tv other than an LCD, there will be no inverter board. This board is on the tv in order to convert the low voltage direct current, that the switched mode power supplies, into high voltage alternate current. Backlights are lit up with this. Inverters boards are sometimes combined with power boards. If your inverter board goes bad, you may see a dim screen or a display that shuts down entirely.
The main board is also known as the motherboard, the logic board, the main module, and the digital board. This is going to be the board on the back of the television that has the sound and video inputs and outputs attached to it. The main board is what takes in the signals and converts analog into digital. If you don't have color or sound, have vertical lines, or no picture, the main board may be the culprit.
The audio receiving board or jackpack can be separated from the motherboard. The jackpack moves the sound signal to a processor and then to the amplifiers that are on either side of your television. If you can't get any sound, or hear a high pitched tone, the jackpack can be the culprit. You should check out the jackpack if the channels start to change randomly.
About the Author:
See the featured products including the d50ud1 by referring to the Web. Spend a minute or two browsing the online store at http://www.tekbyus.com/product-tag/d50u-d1.
No comments:
Post a Comment